Surf City Garage Interior and Exterior Car Detailing Meguiars Car Wax & Detailing Products Auto-Air Colors Water-Based Paint Wizards Car Wash and Shine Flitz Metal Polish & Detailing Wax Sprayway Glass Cleaner and Shine Products California Car Duster California Water Blade
ShineGear.com offers a 100% secure shopping & checkout experience.
Aircraft® Peeler™ Basecoat & Clearcoat Remover Aircraft® Peeler™ Basecoat & Clearcoat Remover is specifically formulated for use on vehicles experiencing delamination problems where top coat of paint is separating from the original factory applied primer. DIRECTIONS FOR USE: 1. Shake well before using. Apply only to a clean dry surface.2. Cover all painted surfaces not intended to be stripped to prevent remover residue from settling and damaging paint. Mask to keep remover from entering seams or trim openings to prevent bleedback stripping of new finish.3. Spray on painted surface while holding can in an upright position, pointing arrow on top of button away from you, at a distance of approximately 8" to 12" from the surface. Use a back and forth motion and apply a light even coating, taking care not to over-apply.4. Allow remover to work for approximately 1 to 5 minutes, or until the paint has sufficient time to blister or bubble. Once the paint has blistered or bubbled, remove the paint and paint remover residue immediately by blowing with shop air. Be sure to cover all painted surfaces to prevent remover residue from settling and damaging paint. Residue can also be removed with a flexible plastic scraper, steel wool or shop rags. If a repeat application is needed, use extreme caution when applying. Overapplying may cause damage to exposed E coat primer.5. Allow cleaned surface to dry, then apply new finish by following manufacturer’s directions. Prime any exposed metal as soon as possible to prevent flash rust from occurring.IMPORTANT: Carefully read all cautions and instructions before use. Protect hands with chemical-resistant gloves and eyes with chemical splash goggles.HELPFUL TIPS: For best results, apply at temperatures between 70°F and 90°F. Avoid direct sunlight or strong breezes. Not recommended for use on fiberglass, plastic or any other synthetic surfaces. Before using on surfaces other than metal, first test suitability. We do not guarantee results on non-factory applied primers.
Aircraft® Peeler™ Basecoat & Clearcoat Remover is specifically formulated for use on vehicles experiencing delamination problems where top coat of paint is separating from the original factory applied primer.
DIRECTIONS FOR USE:
1. Shake well before using. Apply only to a clean dry surface.2. Cover all painted surfaces not intended to be stripped to prevent remover residue from settling and damaging paint. Mask to keep remover from entering seams or trim openings to prevent bleedback stripping of new finish.3. Spray on painted surface while holding can in an upright position, pointing arrow on top of button away from you, at a distance of approximately 8" to 12" from the surface. Use a back and forth motion and apply a light even coating, taking care not to over-apply.4. Allow remover to work for approximately 1 to 5 minutes, or until the paint has sufficient time to blister or bubble. Once the paint has blistered or bubbled, remove the paint and paint remover residue immediately by blowing with shop air. Be sure to cover all painted surfaces to prevent remover residue from settling and damaging paint. Residue can also be removed with a flexible plastic scraper, steel wool or shop rags. If a repeat application is needed, use extreme caution when applying. Overapplying may cause damage to exposed E coat primer.5. Allow cleaned surface to dry, then apply new finish by following manufacturer’s directions. Prime any exposed metal as soon as possible to prevent flash rust from occurring.IMPORTANT: Carefully read all cautions and instructions before use. Protect hands with chemical-resistant gloves and eyes with chemical splash goggles.HELPFUL TIPS: For best results, apply at temperatures between 70°F and 90°F. Avoid direct sunlight or strong breezes. Not recommended for use on fiberglass, plastic or any other synthetic surfaces. Before using on surfaces other than metal, first test suitability. We do not guarantee results on non-factory applied primers.
Aircraft® Peeler™ Basecoat & Clearcoat Remover
Aircraft® Peeler™ Basecoat & Clearcoat Remover Product Reviews : Write a review
My Account Contact Us Return Policy Privacy Terms
Website Copyright ShineGear.com 2008-2011 Ecommerce Websites by OuterBox Solutions
Link to Us! Shine Gear Auto Detailing Sitemap Resources
